WORKSHOP MANUAL SERVICE REPAIR SERVICE REPAIR FERRARI CALIFORNIA (2008-2014) (EN)

This Product is a PDF Workshop manual for
FERRARI CALIFORNIA
2008-2014

TOPICS:
0 General
-01 Manual structure
- 01.01 Consultation
- 01.02 Updates
- 01.03 Symbols
- 01.04 Glossary
-02 General instructions
- 02.01 Manual user
- 02.02 Operating procedures
- 02.03 Using tools and spare parts
- 02.04 Warranty
- 02.05 Tightening torques
-03 Safety
- 03.01 Personal protection
- 03.02 Hazards
- 03.03 Dangerous emissions
-04 Vehicle identification and labels
- 04.01 Label location
- 04.02 Assembly number
- 04.03 Chassis number
- 04.04 Engine type and number
- 04.05 Chassis number
- 04.06 Gearbox type and number
- 04.07 Vehicle identification
- 04.08 Tyres
- 04.09 Antifreeze and expansion tank opening instructions
- 04.10 Fuel
- 04.11 Paintwork
- 04.12 Emissions control
- 04.13 Airbag
- 04.14 Airbag
- 04.15 Airbag
- 04.16 Luggage placement in luggage compartment
- 04.17 Luggage placement in luggage compartment
- 04.18 Engine oil, gear oil and hydraulic clutch system fluid
- 04.19 Engine oil level check and radiator with antifreeze
- 04.20 Safety standard compliance and mercury warning label
- 04.21 Stop&Start system warning label (optional)
-05 Main specifications
- 05.01 Performance and consumption
- 05.02 Dimensions and weight

A Fluids, lubricants and maintenance
-A1 Fluids and lubricants
- A1.01 Fluid properties
- A1.02 Fluids and lubricants table
- Fluids and lubricants table
-A2 Scheduled maintenance
- A2.01 Scheduled maintenance
- PDI form
- Annual maintenance
- 20.000 km (12.500 miles)
- 40.000 km (25.000 miles)
- 60.000 km (37.500 miles)
- 80.000 km (50.000 miles)
- 100.000 km (62.500 miles)
- 120.000 km (75.000 miles)
- 140.000 km (87.500 miles)
- 160.000 Km (100.000 miles)
-A3 Maintenance operations
- A3.01 Checking engine oil level and changing engine oil and engine lubrication
- A3.02 Inspecting oil level and replacing Shell Transaxle 75W-90 GL5 gear oil
- A3.03 Checking Shell DCT F-3 hydraulic clutch system fluid level
- A3.04 Checking the windscreen and headlight washer fluid level
- A3.05 Checking brake system fluid level
- A3.06 Checking the power steering system fluid level
- A3.07 Checking coolant level and topping up
- A3.08 Replacing the active carbon filter
- A3.09 Replacing the oxygen sensor
- A3.10 Replacing the engine air filters
- A3.11 Replacing the air conditioning and heating system filter
- A3.12 Checking tension and replacing auxiliary utilities belts
- A3.13 Checking and replacing spark plugs
- A3.14 Checking Blow-by system pipes and connections
- A3.15 Checking cooling system pipes and connections
- A3.16 Checking injection and ignition system pipes and connections
- A3.17 Checking exhaust system connections
- A3.18 Checking exhaust emissions
- A3.19 Checking service brakes for wear
- A3.20 Checking service brakeparking brake function
- A3.21 Checking suspension components
- A3.22 Vehicle Setup Parameter Check Form
- Vehicle Setup Parameter Check Form
- A3.23 Checking proper installation and function of seats and seat belts
- A3.24 Checking and recharging battery
- A3.25 Checking alternator absorption and recharging function
- A3.26 Checking the state of the chassis and box elements
- A3.27 Checking wheels and tyres
- A3.28 Inspecting the air conditioning and heating system
- A3.29 Inspecting the brake system
- A3.30 Tightening bolts, unions and clamps
- A3.31 Checking and lubricating hinges and adjusters
- A3.32 Treating interior trim in leather - Alcantara
- A3.33 Checking radiators for fouling
- A3.34 Lubricating windscreen cross member seal and Front and Rear RHT Roof
- A3.35 Cleaning and maintaining matt paints (if applicable)
- A3.36 Replacing the transparent film on Tonneau Cover
- A3.37 Service counter reset
- A3.38 Cylinder compression test

B Engine
-B1 General
- B1.01 Technical specifications
- B1.02 Specific tooling and equipment
- B1.03 Tightening torques
-B2 Operations
- B2.01 Removing the complete engine
- B2.02 Refitting the complete engine
- B2.03 Engine overhaul - Disassembly
- B2.04 Engine overhaul - Inspections
- B2.05 Engine overhaul - Rebuild
-B3 Engine fuel system
- B3.01 Engine fuel system layout
- B3.02 Fuel tank
- B3.03 Active carbon filter
- B3.04 Fuel pump assembly
- B3.05 Fuel level sensor
- B3.06 Fuel vapour separator
- B3.07 Draining the engine fuel system
-B4 Engine air intake system
- B4.01 Engine air intake system layout
- B4.02 Engine air duct
- B4.03 Engine air filters
- B4.04 Engine intake manifold
-B5 Engine lubrication system
- B5.01 Engine lubrication system layout
- B5.02 Engine oil pump
- B5.03 Water-engine oil heat exchanger
- B5.04 Blow-by system
- B5.05 Draining and filling the engine lubrication system
-B6 Engine cooling system
- B6.01 Engine cooling system layout
- B6.02 Engine coolant tank
- B6.03 Engine coolant pump
- B6.04 Engine coolant pressure switchthermostat
- B6.05 Engine coolant radiator
- B6.06 Radiator cooler electric fans
- B6.07 Draining and filling the engine cooling system
-B7 Exhaust system
- B7.01 Exhaust system layout
- B7.02 Exhaust manifolds
- B7.03 Catalytic converters
- B7.04 Centre silencer
- B7.05 Exhaust extensions
- B7.06 Silencers

C Transmission
-C1 General
- C1.01 Technical specifications
- C1.02 Specific tooling and equipment
- C1.03 Tightening torques
-C2 DCT gearbox
- C2.01 Gear oil system layout
- C2.02 Removing the complete DCT gearbox
- C2.03 Refitting the complete DCT gearbox
- C2.04 DCT gearbox watergear oil heat exchanger (for vehicles WITHOUT single
- C2.05 DCT gearbox watergear oilclutch hydraulic system oil single oil heat
- C2.06 Draining and filling with Shell Transaxle 75W-90 GL5 gear oil
-C3 DCT gearbox clutches
- C3.01 DCT gearbox clutch hydraulic oil system layout
- C3.02 DCT gearbox clutch hydraulic oil system radiator (for vehicles WITHOUT
- C3.03 Draining clutch hydraulic system and filling with Shell DCT F-3 fluid
-C4 Transmission components
- C4.01 Axle shafts
- C4.02 Transmission shaft
- C4.03 Transmission housing
- C4.04 Flywheel

D Chassis
-D1 General
- D1.01 Technical specifications
- D1.02 Specific tooling and equipment
- D1.03 Tightening torques
-D2 Wheels
- D2.01 Complete wheel
- D2.02 Tyres and rims
- D2.03 Tyre pressure monitoring system (optional)
-D3 Brake system
- D3.01 System layout
- D3.02 Brake fluid tank
- D3.03 Brake discs
- D3.04 Brake pads
- D3.05 Brake callipers
- D3.06 ABS electrohydraulic unit
- D3.07 EPB electric parking brake
- D3.08 Brake servo - Pump
- D3.09 Pedal board
- D3.10 Filling and bleeding the brake system
- D3.11 CCM disc wear form
- CCM Brake Disc Wear Form
-D4 Suspension
- D4.01 Complete suspension
- D4.02 Suspension arms
- D4.03 Hub carriers
- D4.04 Shock absorbers
- D4.05 Stabiliser bars - Tie-rods
- D4.06 Shock absorber set-up adjustment system (optional)
- D4.07 Vehicle set-up
-D5 Steering system
- D5.01 System layout
- D5.02 Power steering tank
- D5.03 Power steering pump
- D5.04 Steering box
- D5.05 Oil radiator
- D5.06 Steering column
- D5.07 Emptying and filling the system
LANGUAGE: ENGLISH